Assemblage d'Extrémité Chaude de Rechange Pour Imprimante 3D Mini Delta (21666)

Assemblage d'Extrémité Chaude de Rechange Pour Imprimante 3D Mini Delta (21666)

  • Sécurité: Soyez toujours extrêmement prudent lorsque vous travaillez sur un appareil électrique, y compris votre imprimante 3D.
  • Assurez-vous que la fiche d'alimentation est retirée et que l'imprimante a complètement refroidi avant de travailler sur l'imprimante.
  • UGS du produit 133684
Disponible: Rupture de stock
€41.99
variant title - Default Title

Ceci est un remplacement Assemblage d'extrémité chaude pour l'imprimante 3D Monoprice ™ MP Mini Delta.

Garantie:
Le remplacement de pièces sur votre imprimante 3D peut entraîner l'annulation de sa garantie. Si vous rencontrez des difficultés et ne savez pas si votre imprimante est toujours sous garantie ou si vous souhaitez éviter l'annulation de votre garantie, veuillez contacter notre équipe d'assistance technique à tech@monoprice.com pour obtenir de l'aide. 

Sécurité:
Soyez toujours extrêmement prudent lorsque vous travaillez sur un appareil électrique, y compris votre imprimante 3D. Assurez-vous que la fiche d'alimentation est retirée et que l'imprimante a complètement refroidi avant de travailler sur l'imprimante.



Monoprice ™ et tous les logos Monoprice sont des marques de commerce de Monoprice Inc.

Au bout de combien de temps vais-je recevoir ma commande ?

Après que votre commande a été placée, l'expédition est effectuée sous 3 à 4 jours ouvrés.

Quel montant dois-je payer pour les frais d'expédition ?

Livraison gratuite à partir de 30€.

Quelle est votre politique de retour ?

Vous pouvez nous retourner vos articles sous 14 jours sans raison particulière. Les articles retournés doivent être dans leur condition d'origine.

Comment fonctionne le retour ?

Si votre article ne vous convient pas, vous pouvez nous le retourner sous une période de 14 jours suivant la livraison. Veuillez nous contacter à eusupport@monoprice.com pour recevoir votre étiquette de retour gratuite. Veuillez imprimer l'étiquette de retour, la coller avec soin sur le paquet scellé puis retourner le paquet auprès de votre bureau de poste local. Merci de conserver soigneusement le document qui comporte le numéro de suivi.

Derniers articles vus

Impression 3D

Pièces de rechange et accessoires pour imprimantes 3D

Customer Reviews

Based on 14 reviews
57%
(8)
21%
(3)
7%
(1)
7%
(1)
7%
(1)
J
Joseph M.
Prints like new

Perfect replacement, my machine prints like new again. It comes as a complete assembly too, so now I have spares from the old one since some parts were salvageable.

R
Randall M.
Does what it says on the tin

(This assembly didn't come in a tin ... )I got this item after pricing out the entirety of parts that come in this assembly separately, and realizing that buying the assembly was much more cost effective and also easier to install.This immediately allowed my MP Mini Delta to print properly and with no thermal issues.I would recommend this for anyone whose hot end doesn't like to heat up unless you manually move the wires (my problem) or if the insulation around the hot end is missing (like mine was).

A
Angel D.
It was ok but broke on 1st day

The first day I got it it failed to work and it broke. So I re ordered another one. Fialment didnt get hot enough.

C
Christopher O.
Used for my mini select v1

I have a monoprice mini select v1 (15365) my nozzle got clogged and in pulling things apart I thought I'd broken some parts of the hot end. For version 1 you can upgrade to the E3D V6 hot end after printing a bracket, which I might since you can get knock offs of that head for cheap, but I wanted too get parts from monoprice. While this says it's for the delta printer it works fine for mini select with the following changes:1. Wires need extended2. remove back portion to allow it to mount to mini select (heat sync has a plastic thing on it you can just take off, mini select has this piece connected to the printer, portion the springs grab onto)3. Keep track of the connections I marked all wires when unplugging from the board (they are not marked at all and all look the same)4. re level bed as the new nozel is not exactly same length (I had to raise my bed about 2.5 twists) you're bed may be different, but will still need adjusted like with any change of the printer.5. I also re used my original fan with it's bracket, but you don't have to.Happy hobby-ing I'm back up and printing

K
Katsuhiro N.
good!

Replacing parts was easy. It's molded smoothly compared to before replacement.

Customer Reviews

Based on 14 reviews
57%
(8)
21%
(3)
7%
(1)
7%
(1)
7%
(1)
J
Joseph M.
Prints like new

Perfect replacement, my machine prints like new again. It comes as a complete assembly too, so now I have spares from the old one since some parts were salvageable.

R
Randall M.
Does what it says on the tin

(This assembly didn't come in a tin ... )I got this item after pricing out the entirety of parts that come in this assembly separately, and realizing that buying the assembly was much more cost effective and also easier to install.This immediately allowed my MP Mini Delta to print properly and with no thermal issues.I would recommend this for anyone whose hot end doesn't like to heat up unless you manually move the wires (my problem) or if the insulation around the hot end is missing (like mine was).

A
Angel D.
It was ok but broke on 1st day

The first day I got it it failed to work and it broke. So I re ordered another one. Fialment didnt get hot enough.

C
Christopher O.
Used for my mini select v1

I have a monoprice mini select v1 (15365) my nozzle got clogged and in pulling things apart I thought I'd broken some parts of the hot end. For version 1 you can upgrade to the E3D V6 hot end after printing a bracket, which I might since you can get knock offs of that head for cheap, but I wanted too get parts from monoprice. While this says it's for the delta printer it works fine for mini select with the following changes:1. Wires need extended2. remove back portion to allow it to mount to mini select (heat sync has a plastic thing on it you can just take off, mini select has this piece connected to the printer, portion the springs grab onto)3. Keep track of the connections I marked all wires when unplugging from the board (they are not marked at all and all look the same)4. re level bed as the new nozel is not exactly same length (I had to raise my bed about 2.5 twists) you're bed may be different, but will still need adjusted like with any change of the printer.5. I also re used my original fan with it's bracket, but you don't have to.Happy hobby-ing I'm back up and printing

K
Katsuhiro N.
good!

Replacing parts was easy. It's molded smoothly compared to before replacement.